Description
The 5V Crimp panel is one of the oldest and most trusted metal panels in the residential industry. A sleek, low profile roof panel with a 1/2" rib height, the 5V Crimp is durable while maintaining high energy efficiency standards.
Features
- Gauge – 29g and 26g galvalume panels
(with 20-year warranty) - Coatings
- Galvalume®
- Panel Attachment - Exposed Fastening System
- Coverage Width – 24”
Section Properties
| Negative Bending | Positive Bending | |||||||
| Panel Guage | Fy (KSI) | Weight (PSF) | Ixe (IN. 4/ft) | Sxe (IN. 3/ft) | Maxo (KIP-IN/FT) | Ixe (IN. 4/ft) | Sxe (IN. 3/ft) | Maxo (KIP-IN) |
| 26 | 80 | .75 | 0.0014 | 0.0069 | 0.2154 | 0.0028 | 0.0061 | 0.2941 |
| 29 | 80 | .95 | 0.0018 | 0.0099 | 0.2849 | 0.0032 | 0.0071 | 0.3695 |
Notes:
All calculations for the properties of 5V Crimp panels are calculated in accordance with the 1996 edition of the Cold-Formed Steel Design Manual, with 1999 supplement - published by the American Iron and Steel Institute (AISI).
Allowable Uniform Loads
( In pounds per square foot )
| 29 Gauge (Fy = 80 KSI) | ||||||||
| Span Type | Load Type | Span in feet | ||||||
| Single | Wind Load Live Load Defection | 1.0 191.5 171.9 | 1.5 85.1 71.5 | 2.0 47.9 30.2 | 2.5 30.6 15.4 | 3.0 21.3 8.9 | 3.5 15.6 5.6 | 4.0 12.0 3.8 |
| 2-Span | Wind Load Live Load Defection | 1.0 191.5 171.9 | 1.5 85.1 71.5 | 2.0 47.9 30.2 | 2.5 30.6 15.4 | 3.0 21.3 8.9 | 3.5 15.6 5.6 | 4.0 12.0 3.8 |
| 3-Span | Wind Load Live Load Defection | 1.0 191.5 171.9 | 1.5 85.1 71.5 | 2.0 47.9 30.2 | 2.5 30.6 15.4 | 3.0 21.3 8.9 | 3.5 15.6 5.6 | 4.0 12.0 3.8 |
| 4-Span | Wind Load Live Load Defection | 1.0 191.5 171.9 | 1.5 85.1 71.5 | 2.0 47.9 30.2 | 2.5 30.6 15.4 | 3.0 21.3 8.9 | 3.5 15.6 5.6 | 4.0 12.0 3.8 |
| 26 Gauge (Fy = 80 KSI) | ||||||||
| Span Type | Load Type | Span in feet | ||||||
| Single | Wind Load Live Load Defection | 1.0 253.2 246.3 | 1.5 112.6 83.4 | 2.0 63.3 35.2 | 2.5 40.5 18.0 | 3.0 28.1 10.4 | 3.5 20.7 6.6 | 4.0 4.0 4.4 |
| 2-Span | Wind Load Live Load Defection | 328.4 189.9 | 146.0 84.4 | 82.1 47.5 | 52.6 30.4 | 36.5 21.1 | 26.8 15.5 | 20.5 10.6 |
| 3-Span | Wind Load Live Load Defection | 395.7 237.4 | 175.9 105.5 | 98.9 59.4 | 63.3 34.0 | 44.0 19.7 | 32.3 12.4 | 24.7 8.3 |
| 4-Span | Wind Load Live Load Defection | 383.3 221.7 | 170.4 98.5 | 95.8 55.4 | 61.3 35.5 | 42.6 20.9 | 31.3 13.1 | 24.0 8.8 |
Notes:
All calculations for the properties of 5V Crimp panels are calculated in accordance with the 1996 edition of the Cold-Formed Steel Design Manual, with 1999 supplement - published by the American Iron and Steel Institute (AISI).
Oil Canning & Ribbing
As a manufacturer of Standing Seam metal roofing, we strive to educate each of our customers about all of the products they are purchasing or may consider purchasing.
Please see attached here some technical/informational articles in regard to Oil Canning for you to read and understand the effects.
In general, oil canning is an aesthetic condition with no effect on the structural integrity of the deck. Since many uncontrollable factors can lead to oil canning, Hercules Sheet Metal and Metal Roofing assumes no responsibility for the cost of actions taken in response to an oil canning condition. Oil Canning is not grounds for panel rejection.
Stiffening ribs or Striations can be added to the center of the panel to minimize the visual effects. The ribbing does not remove the Oil Canning but can disguise the appearance of it. Please indicate below if you would like your product manufactured with or without ribbing.
As the manufacturer we ensure that all reasonable precautions are taken in the ordering of raw material, production, and handling of all material to reduce the appearance of oil canning. We inspect the raw material upon arrival for any defects and confirm that it matches the State of Louisiana requirements as well as inspect the roll formed product to confirm that it matches the specifications of the machine manufacturer and the Louisiana Product Approval quality assurance specification.
5V Crimp Ribbing Disclaimer
Striations and/or Ribbing are minor stiffening ribs in the center of a 5V Crimp panel. It is understood that the striation and/or ribbing is used to minimize the visual appearance of Oil Canning and without it, it may be more noticeable.
Oil Canning is an aesthetic condition and is not grounds for panel rejection.